View camera image in browser?

I'd like to type my ip address in a browser and be able to view the image.

Is there a string of commands that will enable me to do this?

I had it working for a few hours using a string but now I can't duplicate it.

Thank you

http://192.168.1.107/cgi-bin/snap.cgi?user=admin&password=xxxxxx

This was the string that worked for a little while but has now stopped working.

http://192.168.1.107/cgi-bin/snap.cgi?user=admin&password=xxxxxx

This was the code that worked originally

After upgraded the firmware, pls use below URL to get the snapshot:
http://(ip address)/cgi-bin/api.cgi?cmd=Snap&channel=0&rs=(any combination of numbers and letters)&user=(user name)&password=(user password)

For example,
the IP address of the camera is 192.168.2.119
the user name is admin, with the password of 123456
the URL for capturing images would be: http://192.168.2.119/cgi-bin/api.cgi?cmd=Snap&channel=0&rs=wuuPhkmUCeI9WG7C&user=admin&password=123456

Note: Pls replace the ()part to be your camera info.
Every time you refresh the website it will snap a new picture.

For more info about CGI file, pls contact us by support@reolink.com

Thanks! That works for a snap shot but what about a streaming video?

tdwilli1

Dear Gary,

For the stream URL,pls refer to below info:
rtmp://(ip address)/bcs/channel0_(stream type).bcs?channel=0&stream=0&user=(user name)&password=(user password)

Pls replace the () part to be your own camera info.

For example:
rtmp://192.168.2.119/bcs/channel0_main.bcs?channel=0&stream=0&user=admin&password=123456
rtmp://192.168.2.119/bcs/channel0_sub.bcs?channel=0&stream=1&user=admin&password=123456
rtmp://192.168.2.119/bcs/channel0_ext.bcs?channel=0&stream=2&user=admin&password=123456

Dear Gary,

The channel info and steam type is fixed. You need only replace the "( )" part info.

and one more question I had was: If I want to be able to access this camera outside my own wifi what commands do I use? I know I replace the 192.168.1.1 ip with the external ip but what about the rest?

Unfortunately, this is no longer working.

I get 502 bad gateway error using my internal ip code of 192.168.1.107 and I have never been able to access it outside my house even though I have open ports.

I use your iphone app and it uses a UID code to log me in and I can do that remotely just fine.

Is there a way to use this UID code to open a browser outside my home?

OK, when I open your program on my desktop and on the same network as my camera in the Network/Advanced section it gives me the following ports:

9000 media
80 http
554 rtsp
443 https
8000 onvif

Which port would I open to view the camera remotely and please give me instructions to do this?

Can I do a teamviewer with you? Both those ports are open for this camera. I can view it in a browser on my home network now with my local ip address so I know the camera is working but it's just not getting to the outside world.

Or can I privately give you my ip address to check?

Now I can not even view my image on my local network. Getting this error

[ { "cmd" : "Snap", "code" : 1, "error" : { "detail" : "set config failed", "rspCode" : -13 } } ]

9000 media
80 http
554 rtsp
443 https
8000 onvif

ok, do I need to change these settings inside the Reolink software?