Navigation

    Home
    All Categories
    • KEEN Trail Camera
    • Top #ReolinkCaptures Awards
    • Announcements and News
    • Wishlist
    • #ReolinkTrial
    • Discussion About Products
    • Reolink Captures
    • Reolink Client & APP
    #ReolinkTrial
    Reolink Captures
    Log in to post
    Guest
    • Guest
    • Register
    • Login

    Learn More

    Reolink updates Learn More

    Meet Reolink at IFA 2024! Learn More

    Reolink Q&A Learn More

    NVR pre-record compared to Reolink Client

    Discussion About Products
    2
    5
    571
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Richard_17833301777
      Richard last edited by

      Hello,

      Previous to getting a NVR (RLN8-410, build 1609240) I was recording using the Reolink Client (V7.1.2.40) on windows 10 and really liked the pre-record feature.  Once I installed the NVR, I continued to also record with the Reolink Client to compare behavior.

      I do have pre-record turned on on the NVR, however, the Reolink Client always pre-records 5-6 second before the NVR.  I'm not sure how long the pre-record is supposed to be, but I always assumed it was about 5 seconds, so it seems the NVR pre-record may not be working, or it doesn't pre-record very much at all.  (

       

      Is there any way, other than the checkbox being checked, to confirm that pre-record is actually working on the NVR?

      Is there a way to adjust how much it pre-records?

      For additional comparison, the camera is a RLC-411S, build 16091804, and it also has pre-record turned on, and it pre-records to SD about two seconds more than the NVR, and about 3-4 seconds less than the Reolink Client.

      I would like to eventually depend soley on the NVR, but I don't like that it has the least amount of pre-record, or the pre-record isn't working.

      How long is the pre-record supposed to be for each of these?

      Thanks,

      Richard.

      Reply Quote
      Share
      • Share this Post
      • Facebook
      • Twitter
      • copy the link
        Copied!
      0
        View 0 replies
      • Guest
        Anonymous last edited by

        Richard,

        Not an official answer to your question on the pre-record as the manual does not say a number, however the manual does says the following about pre-record, "While Pre-Record is enabled, the NVR will record a few seconds before an event occurs. It’s a little like making the NVR psychic .If you’re using Motion Detection (recommended) based recording as your primary recording method(s), then it’s a really good idea to use Pre-Record - sometimes, if an event is fast enough, it might have left view before the NVR can trigger a recording. With Pre-Record, there’s almost no chance you’ll miss it." (emphasis mine)

        Reply Quote
        Share
        • Share this Post
        • Facebook
        • Twitter
        • copy the link
          Copied!
        0
          View 0 replies
        • Guest
          Anonymous last edited by

          Hi, Richard

          For your 2 questions:

          1, Pre-records are longer on SD card than on NVR.

          It is normal that pre-records are longer on SD card than on NVR. This difference is caused by memory allocation.

          2, It is not available to adjust how long it pre-records.

          Normally speaking, pre-records are 5 seconds approximately.

          And it is not available to adjust how long it pre-records because camera cache only few seconds' streaming, which may not enough to set it optional.

          Reply Quote
          Share
          • Share this Post
          • Facebook
          • Twitter
          • copy the link
            Copied!
          0
            View 0 replies
          • Richard_17833301777
            Richard last edited by

            Thanks everyone for the replies. I'd hoped the NVR pre-record would be at least as much as the Reolink Client or even the camera it self, but since it's due to limited memory in the NVR, I'm guessing it can't be changed through firmware.

            Reply Quote
            Share
            • Share this Post
            • Facebook
            • Twitter
            • copy the link
              Copied!
            0
              View 0 replies
            • Guest
              Anonymous last edited by

              Hmmm, why not use the HDD inside the NVR and use that for pre-record caching?

              It sure is a serious limitation for the NVR solution if pre-record isn't working.

              Reply Quote
              Share
              • Share this Post
              • Facebook
              • Twitter
              • copy the link
                Copied!
              0
                View 0 replies
              • First post
                Last post
              All Categories
              Announcements and News Reolink Client & APP Discussion About Products #ReolinkTrial Reolink Captures Wishlist KEEN Trail Camera
              Never miss Reolink hot deals, news, and updates tailored for you.

              Thanks for your subscription!

              Please enter a valid email address.

              Oops… Something went wrong. Please try again later.

              You are already subscribed to this email list. :)

              Submission failed. Please try again later.

              Reolink Store|Support|About Us|Privacy Policy|Terms and Conditions

              Copyright 2025 © Reolink All Rights Reserved.

              Welcome Back!

              Hi there! Join the Commnunity to get all the latest news, tips and more!

              Join Now