Navigation

    Community
     reolink reolink  reolink reolink
    • Search
    • Store
    • Community
    • Support
    • Register
    • Login

    Problem changing camera position

    Discussion About Products
    2
    5
    38
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • it_484462163448014
      it last edited by

      This is the situation:
      We have 8 cameras, tested connected all to NVR no problems.
      There is a internet line without bandwidth problems.

      NVR connected to GigabilSwitchA and one port with a iniector and a sigle cam connected.
      This switch is connected to the main Router.
      An other GigabitSwitchB(POE) is connected to the main Router.

      Now I have 3 cameras connected to GigabitSwitchB(POE), detected from NVR.
      An other single connected to the iniector connected to GigabilSwitchA, is also detected from NVR.

      But if I replace the camera connected to the iniector with an other camera, or connect the camera to the GigabitSwitchB, is not detected.
      (changing all remaining cameras same problem).

      We have leave connected one camera not functioning to GigabitSwitchB, after some hours have began to work.
      Why is it happening?

      Reolink Fiona 1 Reply Last reply Reply Quote 0
      • Reolink Fiona
        Reolink Fiona Administrators @it last edited by Reolink Fiona

        @it_484462163448014
        You can try to reassign the camera channel on the NVR. Delete the offline camera and scan the camera again. You can refer to this article, https://support.reolink.com/hc/en-us/articles/900003769346-How-to-Delete-Offline-Camera-Information-on-Channel-Management-Page-via-Reolink-NVR-New-UI-. Hope this helps.

        it_484462163448014 1 Reply Last reply Reply Quote 0
        • it_484462163448014
          it @Reolink Fiona last edited by

          @it_484462163448014
          You can try to reassign the camera channel on the NVR. Delete the offline camera and scan the camera again. You can refer to this article, https://support.reolink.com/hc/en-us/articles/900003769346-How-to-Delete-Offline-Camera-Information-on-Channel-Management-Page-via-Reolink-NVR-New-UI-. Hope this helps.

          Sorry but Channel management menu don't exist.
          NVR model is RLN16-410
          Firmware v3.0.0.123_21031206

          Reolink Fiona 1 Reply Last reply Reply Quote 0
          • Reolink Fiona
            Reolink Fiona Administrators @it last edited by

            @it_484462163448014
            Do you use the NVR monitor to view? If your monitor UI is different, you can try to view this article to assign the camera channels.

            it_484462163448014 1 Reply Last reply Reply Quote 0
            • it_484462163448014
              it @Reolink Fiona last edited by

              @it_484462163448014
              Do you use the NVR monitor to view? If your monitor UI is different, you can try to view this article to assign the camera channels.


              We are operating on NVR accessing via Web (on the same LAN).
              At this point I understand that the interface by connecting the device directly is more complete than that via the Web, we did not know it (we will do the tests and update you).

              Regards

              1 Reply Last reply Reply Quote 0
              • 1 / 1
              • First post
                Last post
              Reolink cloud reolink reolink Reolink cloud reolink reolink

              Reolink Store|Support|About Us|Privacy Policy|Terms and Conditions

              Copyright 2021 © Reolink All Rights Reserved.