When entering full screen mode, currently the only way to exit this mode is by pressing the ESC key.
My Windows 10 touch screen tablet has no keyboard hence if have no way to exit full screen mode.
Hence request that the developers should in a future release to include a method to exit full screen mode when using a touch screen device.
I suggest to add a small touch button in the lower right corner of the screen where there are existing touch buttons for taking screen shots etc, and program the new button with the ESC function. Quite a simple task for the software developer team.

Robert Hammond
@Robert Hammond_315369854550200
Best posts made by Robert Hammond
-
RE: Reolink Client Ver. 8.4.0 Beta Test Is Open!
Latest posts made by Robert Hammond
-
RE: Reolinkers’ Week Day 5: Reolink Client Version 8.7 Beta & APP Version 4.29 Release
With the Client Version 8.7 Beta
The live camera view defaults to Standard view (which I think is the same as Fluent). And I can change the camera view to Clear by right clicking on the live image. This setting change will remain while the client is running.
My recollection with the previous client version was that after changing the live view to Clear, this setting change would be saved so that when starting the client after shutting down, the client would boot the live view to Clear.
Observation with 8.7 Beta - changing the live view to Clear is not save after a client re-boot. -
RE: Reolink Client Ver. 8.4.0 Beta Test Is Open!
@robert-hammond_315369854550200
Replying to my own post.
The full screen mode can be quite complex if you display multiple cameras.
So suggest a simple way forward would be to program using a 'Double Tap' to exit full screen mode on touch screen devices -
RE: Reolink Client Ver. 8.4.0 Beta Test Is Open!
When entering full screen mode, currently the only way to exit this mode is by pressing the ESC key.
My Windows 10 touch screen tablet has no keyboard hence if have no way to exit full screen mode.
Hence request that the developers should in a future release to include a method to exit full screen mode when using a touch screen device.
I suggest to add a small touch button in the lower right corner of the screen where there are existing touch buttons for taking screen shots etc, and program the new button with the ESC function. Quite a simple task for the software developer team. -
RE: 940nm IR illiuminators
I have some experience.
Some time back I spotted a youtube product comparison that seemed to show the the RLC-1220A had very good night vision so I purchased one to use for my low down Badger Cam project. I have it mounted about 50cm above ground level and have configured with the supplied 850nm IR function turned off.
I supply the 940nm IR lighting using an illuminator that I purchased on line and seems to be reasonably successful.
Currently the streaming video has a dark shadow away from the light source because the illuminator is mounted higher than the camera.
When I get time my plan is to have two illuminators, one each side, each with a variable voltage control to minimise over exposure. -
RE: Client Beta V8.0.5 problem
Hello Cynthia
I have also been trying out the 8.0.5 beta on both my PC and also a Windows 10 touch screen tablet.
It is normal practice when debugging beta software for the software developers to use feedback gained from forum postings posted by the wider user community so have posted to this particular message thread. I hope that your software developers monitor the forum.
I would like to report two software problems with this version.
1. The first issue is due to running the software on a windows 10 32 bit touch screen device that does not have a keyboard.
If I expand the video screen using the double arrows in the bottom right corner, I cannot then exit this mode because the exit method involves pressing the Esc key but a touch screen device has no Esc key. Perhaps your software developers could incorporate using a double screen tap or some other method for exiting full screen mode when using touch screen devices.
2. The second issue, I can adjust the motion alarm sensitivity but there is no way to save the setting. The sensitivity setting reverts back when the settings page is closed hence a relatively major issue.
Regards Robert