Share Your Local Security Installation to Win Cameras
Get Your 25% OFF for Local Storage NVR Kit Now
Talk About the Local Storage: Pros/Cons and Local Storage Options
Bringing Up New Products Check Out What's Coming Next
Where to install the 360° Reolink Fisheye? Here are recommended Positions
I am having no luck at all with getting "Client" to work with my NVR.1 year old system. POE, Ethernet cable from NVR to my router. If I disconnect the ethernet cable I get a warning on screen that there is no connection - so I assume the NVR is actually connected. I install Client on my PC and it never connects to the NVR. I have deleted and re-installed, entered the NVR UID when asked by Client and keep getting ERROR.I have updates available but cannot install because of no connection from Client to NVR.I'm at witts end and there was never a lot of witts to begin with.NVR is N3MB01.Any help will be really appreciated.
@zalmaflash_316143213592812 You can try to upgrade your NVR with the latest firmware. You can download the firmware v22.214.171.124_21122405 below.For RLN8-410 with hardware version N3MB01: https://drive.google.com/file/d/1KFOOcHHMen1oDJJM0i9WD-VNwcnJjMYD/view?usp=sharing
@reolink-fiona Thank you for the reply. If I ever get "client" to work on my PC I will do the upgrade to the NVR.
@reolink-fiona On the NVR "DDNS" settings it asks for a domain name, username, and password. I didn't know what to put there so I left it blank. When I press "Test if setup succeeded" I get a failed pop-up.What do I put in these spaces? I have the internet of course but I don't think I have a domain name?
@zalmaflash_316143213592812 Hi there, you can upgrade your NVR firmware directly on the NVR monitor that is connected to the NVR. Then you can input the UID and password of the NVR on the Client. Finally, you can connect the NVR to the Client.
@reolink-fiona I GIVE UP! Is there a way to completely start over from scratch - like new out of the box? Doing it all with just the cameras and monitor and a cat 5 patch cord connected to my router? This is not working for me.
@zalmaflash_316143213592812 To explain more. Apparently I did something wrong on the initial out of the box startup. I do remember a "START up WIZARD" = and I cannot get it to show up again to start over. Is there a way to get it (start up wizard) back and some instructions that actually match so I can try it again? Do I need to send it in for reset?
@zalmaflash_316143213592812 Hi there, here is an instruction about how to initially set up the NVR connected to the monitor.https://support.reolink.com/hc/en-us/articles/900005458466-How-to-Initially-Set-up-PoE-NVR-with-Monitor-Connected-New-UI-If you can't make it work, you can try to reset the NVR.https://support.reolink.com/hc/en-us/articles/900000593463-How-to-Hard-Reset-Device-by-Pressing-the-Reset-ButtonHere is the method to add your NVR to the Client after the initial set-up.https://support.reolink.com/hc/en-us/articles/900003548586-How-to-Add-Reolink-Products-in-LAN-via-Reolink-Client-New-Client-
@reolink-fiona Thank you - I will give the reset and the instructions a try. Thank you for your patience.
Also the instructions for client do not seem to be downloadable.I'm doing something wrong and do not know what.
When the NVR is connected to your home network, there should be an entry in the network management showing the IP address that was assigned to the NVR.(I typically use a router feature to "permanently assign" an IP to things like printers, file servers, NVRs, etc. so that they will always have the same IP every time the router restarts or power is restored after an outage.)I would try putting the IP address into the Client program to search for the NVR.DDNS is a method used to connect from the Internet into a local network and is set up on the customer's router. It should not be required when the client software is installed on a computer on the same network as the NVR.
@crimp-on_62210811129 Going to try it. Thanks
@zalmaflash_316143213592812 i TRIED THAT AND IT CAME BACK "NO DEVICE FOUND". Then I also tried the UID of the NVR in lower case. Didn't work either. Now, I do have a home network that is just for my computers. But I don't think it has a name. Can you tell that I am confused?
What type of computer is the Reolink Client running on?Can you open a command window and 'ping' the NVR by its IP address?
@crimp-on_62210811129 The computer is a laptop LENOVA.
@zalmaflash_316143213592812 Couldn't edit to add the os is windows 10. I also have an HP with windows 10 and have the same problem. I do not know how to "ping" something. Both of my comps are wireless connected to my router. The NVR is hooked direct to the router with a cat6 patch cable.
Hi there! Join the Commnunity to get all the latest news, tips and more!