Best posts made by Alvaro2

@Reolink-Fiona It would be a good idea to design a camera in the style of E1 outdoor or RLC 823a (rotating) but for the interior of the vehicle.
This would be powered by a battery that could be charged to the USB-C of the car and the data could be processed via 4G or 5G when the car is off and via the car's Wi-Fi when it is on.
It could also equip a solar panel that could be left on the dashboard to take advantage of and charge the battery when the car is in direct sunlight.
The fastening could be by suction cup to any window on the inside of the car or to the panoramic roof.
As main specifications I think that about 5mpx would be adequate at about 20fps, but perhaps a reinforcement of the coverage (more powerful antennas) is recommended.
It could also be equipped with a motion sensor, so if a hit is detected in the car, the camera proceeds to record what has happened and it could also be used as a sports camera, but there I would bet on 8mpx and 30-60fps. It could be a hybrid surveillance/sports camera.
In terms of size, I think it should be a bit smaller than the E1 outdoor.

I think this is an excellent idea and I would like this suggestion to be passed on to the appropriate department for feasibility.
Thank you very much for your attention.

Hello @Reolink-Fiona I have already contacted the support service, but I would like to report the problem I have had here. On February 12, I updated my E1 Outdoor to version 3.1.0.1584, but two days ago I began to notice that the live broadcast of the camera was not going well. Not only that, this bug must hit something from the other wi-fi camera I have (the E1 zoom). When I was running the 8.10 beta desktop version, both cameras were malfunctioning, to the point where the E1 zoom would broadcast on the screen where the E1 outdoor was and vice versa, in clear mode it was restricted and closed at any time either camera .
After doing tests I have come to the conclusion that the fault is in the firmware version 3.1.0.1584 of the E1 Outdoor.
The solution has been to download the E1 Outdoor to version 3.1.0.989 and everything is perfect again.

@reolink-fiona great, looking forward to try it, but I don't have my PC with me until next week. Wait for me please!!

Hello @Reolink-Fiona I would like to make several suggestions for both the cameras themselves and improvements to the app.
1) It would be nice to think of a third color for cameras, especially outdoor ones, such as the RLC-1212A, 812A, 823A. That color could be anthracite gray for example, and according to my point of view it is a color less suffered when it comes to being outdoors.
2) Improvements in the app. Although I am testing 4.33.05, I think it is necessary to incorporate in future updates the direct access button to timeleapse in the lower bar where the image quality buttons, take a photo, etc. are, or even in the conversation bar, PTZ, etc. (As it is in the PC version).
3) Improvements in the firmware of the Argus 3 Pro. I have FW 3.0.0.973_2205 and when I want to view the image the connection is cut and "operation failed" appears, other times it takes 5-8 seconds to load and is slow.
An option should also be allowed in battery-powered cameras and that is that when it is connected to a solar panel, that the energy comes from the panel and not make the battery suffer or that the camera uses the battery between a certain range and from the solar panel in another range. So it could be "normal" display such as Wi-Fi or PoE.

Consider these suggestions. Thank you very much.

Answered. Thanks you!

@Reolink-Fiona testing client 8.8.0, one improvement could be hiding the buttons of zoom, snap, record, etc. if the mouse don´t move for example in 3 seconds. Other improvement could be setting the image quality from the general settings. I am testing all and I have no problems yet.