@user_822884704698612_822884704698612

Need more details on how its connected? using POE switch?

You cant see your DHCP table within your router? There should be a list of connected clients within the router.

If you could bring the camera down plug it up closer to the router with a short drop cable, that will confirm is there is a faulty cable or cam.

Super awesome footage dude!

@user_603788725944329_603788725944329

Add them per their UID that will create the cloud link between your app and the cams.

I think you need to look at what you are needing.

Ultra wide is ultra...wide. But it usually has a very small vertical FOV. Unlike the 1240A, which had a huge FOV, but not as wide as the ultra-wide cams.

I prefer the ultra wide if I'm trying to capture a large area. Then i use other models when I need more accurate view.

It would be nice to have a 3 cam or a 2 cam option for Duo cams. Where it shows 2 duos as widescreen. or 3 cams with the 1 duo at top as wide screen and 2 cams below in a squared box.

PC Client already does it, with 2 cam setting.

Currently the only has a 4 cam option.

@chopstix

My cam shows charging when the sun is out. It shows a lightning bolt over the battery icon.

It hasnt charged since we are heading into another winter storm, polar vortex. Lots of cloud cover. Supposed to be sunny tomorrow but cold but we will see.

I did have a lot of fragmented recordings until I adjusted the monitor point timeout and raised my PIR to the max. it’s less now.

But this is my backyard, it’s not a highly active area. It’s really to cover my front and back door.

@reolinkshayla

Finally a battery powered door bell! Been waiting for this for a long time!!

Will it have capabilities for a solar panel?

@user_830676047601836_830676047601836

I know on my reolink nvr, there is a auto scan feature when trying to add a cam to a channel. Does the Amcrest cam show up in that list?

@chopstix

Since your post, I've been watching my camera's logic. I get very few fragmented recordings, but I feel like it happens when my wife and dog barely step out of range of the PIR sensor and steps back in. Increasing the "Time to Stop Tracking" to 1 Mins for both options seems to drop fragmented recordings a little more on my end.

This is my 1st battery/solar cam in my system. I have all POE cams. It has been a doozy pin pointing these settings for my scenario.

@johnsonm2_326272226037961

So if you did a factory reset... You will need to add the cams back to the channels.

The network ports the non functional cams are plugged into, do they have lights blinking on them? Want to confirm their active and hot.

I dont think the CX820 is a PTZ cam.

Super awesome footage dude!

@reolink-oskar

I dont have one... Yet. If you want to send me one, I will gladly run through it and post my findings here.

@user_603788725944329_603788725944329

Add them per their UID that will create the cloud link between your app and the cams.

@joseph_1979 Thanks for the info! That makes way more sense.

@joseph_1979

@Chopstix

Reading on the FB group, that the current Solar Panels can not keep up with the unit on full time recording is a question mark for me. if its full time recording and the panel has a long period of sunlight, it can't keep up. I know it's probably outputting more power than taking in... Small part of me hopes they would make a bigger panel for the Altas. However, I wouldn't mind buying a bigger panel for it, if I could get more energy pushed to it.

@joseph_1979

Ah gotcha! Thanks for the explanation! It being 6F today and sunny, no charge... Now I know why.

So far, this camera has performed to my needs. it has been operating at 0F and -10F wind chills. So far so good.

@chopstix

LOL you are 500% right!

Its 0 degrees out right now... Bright, sunny, and not a cloud in the sky... and not charging. I wonder if the outside temp affects the solar panel? I wiped off the panel with a clean terry cloth rag, it looked "dirty", and no go. Unplugged the USB cord and reseated it, nothing. From 1pm till now (3:38pm) not charging.

It was working the week before until it got super cold. I'm assuming the cold weather is affecting it.

@reolink-oskar

Bring back the POE flood light. Or add every camera's spotlight into the "linked devices" so we can create "scenes".

Motion zones versus the non motion paint brush.

LPR feature or a LPR cam.

Software based NVR. So we can self host.

@chopstix

Forgot to mention this... Watching your video. I think your windchime distracts the camera. I had to disable "Other" Motion in the schedule detection type under recording. To reduce that cam confusion. I have this stupid bush that would distract my cam while it waves in the wind. I wish I could just cut it down, but my wife loves it. it would sit on the bush while my wife would keep walking the dog.