Reolink updates Learn More
Meet Reolink at IFA 2024! Learn More
Reolink Q&A Learn More
Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you have been placed in read-only mode.
Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).
@thierry_835077729128592 Oui, vous avez besoin de l'IP ou de l'UID. Je formaterais la SD et vérifierais que la caméra fonctionne correctement avant de la connecter au Home Hub. Faites tous vos tests avant de l'installer. Prenez le temps de vous familiariser. Connectez-le ensuite au Home Hub et c'est le seul moyen d'accéder à la caméra. Uniquement via le hub domestique. Nous avons également demandé un accès direct mais nous n'avons reçu aucun retour.
@flashmagnum_909351053578484 I suggest you to submit your request to support on support @ reolink . com. We are customers like you assisting members wherever possible based on our skills and experience.Note that when I see them separately, it is the same as the RLC-811WA, E1 OD Pro, Argus 3 Ultra, etc.
@chopstix Let me give some details on SIM.Every mobile operator orders SIM cards from SIM manufacturers. Each SIM comprises an identifier ICCID, IMSI and the authentication key Ki amongst other parameters and applets. The Integrated Circuit Card Identifier (ICCID), an identifier of the actual SIM card chip itself. ICCIDs are also used to identify embedded SIM (eSIM) profiles. This ID can be up to 23 digits long, including a check digit calculated using the Luhn algorithm.The International Mobile Subscriber Identity (IMSI) identifies SIM cards uniquely by their individual operator in a cellular network. The IMSI is stored as a 64-bit field and is communicated to the connected cellular network. In the core of a mobile operator network, the IMSI is used as main identification for obtaining further customer and device specific data.All SIM cards contain cryptographic keys. The secret authentication key called Ki is unique and is stored on the ROM, a protected area of the SIM. The Ki is never exchanged between the mobile device and the network. Its purpose is to derive sub-keys that perform the necessary authentication procedures when a mobile device tries to join a carrier’s network. The Ki is also stored on the carrier’s network within a component called the Home Location Register HLR or lately with the introduction of 4G and IMS this is being referred to Home Subscriber Subsystem (HSS). The Ki is only known by the SIM manufacturer and a few persons handling the HLR programming. The IMSI and the Ki have to be inserted in each subscription.So when you switch on the camera or smartphone, there is the IMSI attach whereby the mobile will forward the IMSI to the Radio access network (BTS for 2G, NodeB for 3G, eNodeB for 4G) and from the RAN to the MSC (for calls) and SGSN (3G data) or MME (4G data). This IMSI attach message will end up in the HLR which shall authenticate the SIM. So if the IMSI is defined on the HSS then the IMSI attach procedure will continue otherwise it will be rejected. And an IMSI can only belong to a mobile operator. Thence to connect to another mobile operator you need another SIM card which has different IMSI identifier. The MCC is the same but the MNC and SN will be different.I hope that Reolink should start to add eSIM where there is no longer the need of any physical SIM. This innovation offers the same functionality as a regular SIM card but with an added unique capability: it is programmable, allowing for enhanced flexibility and ease of use. This programmability empowers users to seamlessly switch network operators without needing to physically swap cards. You just buy a plan and they will ask you to scan a QR code and then enter some details the details (like apn)Now a GSM module integrated on smartphone or any device to be connected to GSM network is continuously checking the power of adjacent cells. If the calculated power is better that the one being connected to, the module shall request a location update to the mobile RAN with the new cellid it wishes to connect to. It could be a 3G cell rather than 4G depending of the module is allowed to anchor to 3G (UTRAN) networks. It could be that the mobile is on the edge of an area and it will be continuously changing LAC/RAC/TAC. So I guess that in their previous 4G cameras, the GSM module was not able to compare the power of adjacent cells and request a LUP. I know this area quite well :). And now there is VOLTE which requires IMS.
@user_817261050261638_817261050261638 Most probably you purchased the 3W solar panel. I have the 6W solar panel with the Reolink DUO 2, Argus 3 Pro and Ultra, Argus 4 Pro and have no issues as long as there is 2 hours of direct sunlight. On the Argus 4 Pro I get around 2 hours of battery usage per day.But yes I agree that they should provide higher wattage solar panels esp in places with short periods of direct sun and higher capacity batteries (like the Altas PT ultra). Nevertheless you did a good job. Well done. I don't ask any question as I know all the theory :).
@ddelrosso_61389620748490 That's it.
@chopstix Thanks. Exactly this is not the immersive view but rather the dual view or separated view. When the icon shows one dark box then you shall see both the widescreen and the telephoto views on the same screen. Conversely, when the the icon shows two boxes then the widescreen and the telephoto views are on different screens. Just wipe back and forth to get the two views.
@kimchigun Let make some calculations.20,000mAh is 20 Ah. The battery capacity, volts times amp-hours, is about 3.6 x 20 = 72 Wh. The maximum input power is 5 x 1.2 = 6 W. Assuming a 10% power tolerance from the panel (regulator) the charge time in bright sunlight, continually facing the sun, would be 72/6/0.9 = 13.3 hours. However the charge might taper the charge current towards the end of charge so it would actually be longer than that....say 16 hours. Therefore we need a higher wattage solar panel .... at least a 12W panel which yields to 7 hours of bright sunlight.
@chopstix That means that we are reading what you write :). Joking. Sometimes I text while in a boring meeting which I don't chair and won't check my typing....
@chopstix Agree. But it would be more flexible if the camera can provide a number of monitoring positions which can be scheduled by the user. Maybe during the day positioned towards location A, afternoon towards location B and during the night towards location C. This has a pan of 355 degrees and so would be nice to add.
@chopstix eh... it is not Atlas but Altas. The objectives of this cam are being CX, having a higher battery capacity and able to provide pre event detection recording. I think this is the first on the market to provide this pre recording. WELL DONE.
@maxuline Battery operated cams tend to have less frequent firmware upgrades. Lately they are upgrading the firmware of batteries cams like Argus 3, Atlas, etc to integrate with the home hub and some NVRs. Since the battery fw is not included in their download center, every 6 months I email support on support @ reolink . com to check for any newer firmware for battery operated cams.
@ddelrosso_61389620748490 I have the WIFI DUO 2 and this is set to event recording. The maximum recorded video per event is 5 min on the SD. If the object is still within the FOV, another file is opened.I only use sd, ftp and HA. Do you set the video file length on NVR?https://support.reolink.com/hc/en-us/articles/900000640023-What-is-the-Record-Length-on-Reolink-Client/#:~:text=on%20Reolink%20Client-,The%20Record%20Length%20on%20Reolink%20Client,set%20to%205~60%20minutes.&text=Go%20to%20Client%20Setting%20%3E%20Local,change%20the%20Video%20File%20Duration.
@mzumwalt1_471118459977909 The simplest method is to replace the SSID and password on the router side with the previous ones. If, however, the cameras are within reach then change the SSID and password of the hotspot on your smartphone to correspond to the old ones. Then move smartphone near camera and use the appl to access cam. Then connect cam to new WIFI SSID. If you forgot the password of the previous WIFI network then you need to reset cams.
@kimchigun Experience is the best teacher and Reolink should learn from these teachers. ha ha ha......
@reolink-oskar In the past I recall that Reolink have exposed the shutter speed/gain but these are no longer available. These have now been removed as indicated below. "ispExposureMode" : { "permit" : 0, "ver" : 0 }, Would Reolink consider to re-introduce them?In addition we are only able to adjust the brightness of the spotlight but not of the IR. We did ask for a schedule for these functions but so far no feedback. This is a simple software timer. Include it as part of the state machine. Very simple to implement. Question: Is Reolink abandoning the Windows/Mac clients and focusing on Android/IoS?
@chopstix Regardless of the chemistry (uh the days where we had to learn all those formulas !!) of the batteries implemented on Reolink bat cams, cold weather will impact their ability to function. Since batteries run on chemical reactions, and as temperatures drop, these reactions are slowed down and increasing the resistance (the electrolyte becomes more viscous and less conductive at low temperatures), limiting the battery’s operating capacity. Even though lithium-ion batteries perform the best in cold temperatures, they still have a safe operating temperature range that should be followed. Additionally, they have a built-in Battery Management System that prevents them from unsafe operating conditions and won’t allow the battery to operate outside the safe temperature range or accept or charge when the internal temperature of the battery drops below 25°F. Reolink states that their batteries should be charged at temperatures between 0°C and 45°C (32-113°F), and do not use the camera if the temperature drops below -10°C(14°F). But this is the engineering threshold which is lower than the design one. It will operate at more extreme temperatures as customers have witnessed. This, of course, reduces life span and performance. Here in Europe it's sunny with temperature reaching 18 degrees Celsius.
@kimchigun What to expect with 'any motion' enabled! Any change in pixels will trigger a detection. On all my 20s cams I only enable AI detection. FYI there are some issues on playback on the new v4.52 Android client.
@chopstix never laziness shall take over in whatever the situation is. Have goals, challenge and be motivated.
@peter_748442346729617 if you are after a good facial recognition camera then you need to look for expensive cams running in hundreds of bucks. So the question in your case is whether to deter or spy.
@kimchigun if the cam doesn't detect motion for about 10s it stops recording. Increasing the PIR will enable motion to be detected a bit farther away and so it continues to record on the same clip.
Welcome Back!
Hi there! Join the Commnunity to get all the latest news, tips and more!